Oh and congrats to Audi and the R15 on yet another victory at the 12 Hours of Sebring.

This made me think of Pedwar’s eldest brother.

Oil is changed to German Castrol Syntec 0W30. Tranmission is filled with Motorcraft Full Synthetic Manual Transmission Fluid and the differential is fully of RedLine 75W90.

I’ve also acquired a used Hard Dog Hard Core M2 Double Diagonal. Getting it used saved me enough coin that I’m able to get powercoated silver to match the car’s rims, which are also being repaired.

So spring will see me change the brake rotors (already acquired), pads (either Hawk HPS or Carbotech), and fluid (ATE SuperBlue or Motul 600), install the rollbar, and change the clutch and power steering fluid.

I’ve also learned a lot more about the the modifications I had planned so I’ve revised my plan a bit:

Mazdaspeed MX-5 Modification Plan

Rev 2 – 2008.12.07

2009:

1. Hard Dog Hard Core M2 Roll Bar with double-diagonal – safety first, right?
2. Flying Miata Frame Rails – increase chassis rigidity to reduce noise, vibration, and harshness while helping the suspension to do its work
3. Rims and Tires for Solo II – still not sure what to get, but 15″ rims are likely. Also thinking of moving up to R-compound tires, but overall width is where I’m stuck as I want to go wide, but have enough clearance that I don’t have rubbing when I upgrade suspension down the road.
4. Flyin’ Miata Intercooler – this one is a maybe and will depend on budget

Date To Be Determined:

1. Flyin’ Miata Big Enchilada Package

As far as routine maintenance, next spring will see Ginger receive:

• new transmission fluid (Motorcraft Full Synthetic Manual Transmission Fluid) – done
• new differential fluid (RedLine 75W90) – done
  
• new brake fluid (TBD DOT 5.1)
• new power steering fluid (Dexron VI)
• new clutch fluid (TBD)
• brake service (rotors replace or turned), new pads (brand TBD), lubricated
• interior shampoo

My experience with lowering Zhaan and giving her a sport shifter has convinced me that judicious modding can improve any car by making it better tuned to meet the owner’s preferences and needs.

For Ginger, my biggest irritation is related to the evil that is common to all convertibles — chassis flex resulting from the floor serving as the only link between the front and rear of the unibody. There is only so much one can do for this as it is convertible and adding a ton of weight would be contrary to the Miata’s low-mass design ethos.

The next area isn’t so much an irritation as it is an area for improvement — power. 177 horsepower in a car that tips the scales about about 2500 pounds equals pretty decent acceleration, but turbo lag is an issue and let’s face it, one can always benefit from more power. That said, I don’t really want to open-up the engine or make really major changes (yet), particularly as the car still has two years of powertrain warranty.

With this in mind, here is my current modification plan for Ginger:

Mazdaspeed MX-5 Modification Plan

Initial Draft – 2008.11.01

2009:

1. Hard Dog Hard Core M2 Roll Bar with double-diagonal – safety first, right?
2. Flyin’ Miata Butterfly Brace – increase chassis rigidity to reduce noise, vibration, and harshness while helping the suspension to do its work

2010:

1. Flyin’ Miata Downpipe & Catalytic Converter
2. Flyin’ Miata Complete Intake Kit

2011:

1. Flyin’ Miata Exhaust
2. Flyin’ Miata Intercooler *

2012:

1. Who knows, but this page looks interesting and so does this one.

The intercooler has an asterisk beside it because where it places in the order will depend on how the car performs in the heat of summer — I’ve only driven it in cool fall weather. If the tiny stock intercooler does the job, then it will be last, but if I find it struggling to cope, it might move up the priority list.

As far as routine maintenance, next spring will see Ginger receive:

• new transmission fluid (Motorcraft Full Synthetic Manual Transmission Fluid)
• new differential fluid (TBD GL-5/75W90)
• new brake fluid (TBD DOT 5.1)
• new power steering fluid (Dexron VI)
• new clutch fluid (TBD)
• brake service (rotors replace or turned), new pads, lubricated (brand TBD)
• interior shampoo

I’d like to do all of this work myself and with the exception of the welding of the exhaust, there’s nothing to stop me from doing all of it. However, the roll bar needs to be done properly and involves some non-reversible cutting and drilling, so I might look into getting that done professionally, or at least get some experienced hands to help.

It’s going to be very hard putting her for the winter, an activity that is planned for this coming week.

• Model 43UWX10B
• Chassis: GP14G
• Manufactured: August 2001
• IC Model Numbers: STK992-110

Hopefully, over the coming week, I can find all parts, learn how to solder and de-solder, and effect the repair.

Update: Parts ordered! Got two kits with the newer STK992-150 chips for $112.92USD shipped.

That’s where the internet, and more specifically hdtvoice.com comes in. A quick Google search pulled up this thread, which might contain a do-it-yourself fix for our problem.

While it would be nice to get a newer, more compact set with 1080p resolution, we’ve only had this set about six years and we really don’t feel the need to drop a couple grand on a TV right now, so hopefully, this fix applies to our set and I’m able to execute it without causing further damage.

Dynolicious revs auto performance meter for iPhone, iPod | Car Tech: An automotive blog from CNET – CNET Reviews.